A: switchport access vlan 2 switchport mode access
B: port link-type access port default vlan 2
C: port link-type access port default pvid vlan 2
D: port link-type access port trunk allow-pass vlan 2
举一反三
- 以下哪一个命令可以将华为以太网接口改为access模式( )。 A: port link-type access B: port link-type trunk C: port mode access D: port access vlan 10
- 根据如下所示的命令,下列描述中正确的是()。 [Huawei-GigabitEthernet0/0/1]port link-type access [Huawei-GigabitEthernet0/0/1]port default vlan 10 [Huawei-GigabitEthernet0/0/2]port link-type trunk [Huawei-GigabitEthernet0/0/2]port trunk allow-pass vlan 10
- 华为交换机的某一个端口另一台电脑口相连,需要做出什么样的配置() A: port link-type access B: Switchport mode access C: Switchport mode trunk D: Port link-type trunk
- 在华为交换机中设置接口为静态访问模式的命令是( )。 A: [SW1-G0/0/1] switchport mode access B: switchport mode trunk C: port link-type access D: port link-type trunk
- 华为交换机中把当前端口设置为access模式,正确的命令是( )。 A: [Huawei-Ethernet0/0/1]port mode access B: [Huawei-Ethernet0/0/1]port link-type access C: [Huawei-Ethernet0/0/1]switchport link-type access D: [Huawei-Ethernet0/0/1]switchport mode access
内容
- 0
配置交换机端口的Trunk模式正确的是() A: <;H3C>; int g1/0/1[H3C -GigabitEthernet1/0/1] port trunk permit vlan 10[H3C -GigabitEthernet1/0/1]port link-type trunk B: [H3C] int g1/0/1[H3C -GigabitEthernet1/0/1]port link-type trunk[H3C -GigabitEthernet1/0/1] port trunk permit vlan 10 C: [H3C -GigabitEthernet1/0/1] port link-type trunk permit vlan 10 D: [H3C] int g1/0/1[H3C -GigabitEthernet1/0/1] port trunk permit vlan 10[H3C -GigabitEthernet1/0/1]port link-type trunk
- 1
下面哪条命令可以配置华为交换机的端口为hybrid模式? A: switchport hybrid B: port hybrid enable C: port link-mode hybrid D: port link-type hybrid
- 2
(网络)华为交换机将某个接口配置为trunk模式命令为? A: interface 接口号; switch-port mode trunk B: interface 接口号; port link-type trunk C: interface 接口号; port link type trunk D: interface 接口号; switch port mode trunk
- 3
要将某个交换机端口划归VLAN,应该接口设置为什么模式?() A: access模式 B: multi模式 C: trunk模式 D: port模式
- 4
为交换机端口指定VLAN的配置命令是 A: Switch(config-if) # vlan-menbership static B: Switch(config-if) # vlan database C: Switch(config-if) # switchport mode access D: Switch(config-if) # switchport access vlanl